PLUMBING BASICS: WHAT YOU NEED FOR BATHTUB INSTALLATION

Plumbing Basics: What You Need for Bathtub Installation

Plumbing Basics: What You Need for Bathtub Installation

Blog Article

Call

Just about everyone has got his or her own idea on the subject of How to Install a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately hard project. If the old tub is conveniently obtainable, the project can relocate speedily; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and set in the brand-new one. Ensure you have certified on your own for the job as well as fit attempting it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually currently purchased a new bathtub and also do not need to transform the plan of your previous water pipelines.
Your tools and product list ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain any water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited accessibility that is frequently the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
    Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the maker supplied backnut. When the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type should be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Setting up the Tub


    Making use of the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the bathtub up until the level reads level.
    To mount faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
    Activate the water supply and inspect all joints and also new pipework for leakages as well as tighten them if necessary. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will certainly settle it into its last placement.

    Preparing for the Setup


    To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
    Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last position.

    Tiling Around the Bath tub


    In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, leading to problems with dampness and also possible leaks to the ceiling listed below.
    You can choose from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can break fairly early if you do not take into account this movement prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles making use of waterproof or water resistant adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I have been very interested in Installing A Bathtub and I hope you appreciated the blog entry. Sharing is good. You just don't know, you may very well be helping someone out. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Need pros? Call!

    Report this page